Antz5SFE's Posts - 6GC Forum Archive

📝 Antz5SFE's Posts

Antz5SFE

📍 Philadelphia, PA

Member

Posts

116

Vehicles

🚗 View Vehicles

any temporary fixes to make an exhaust leak sound better? - 6G Celicas Forums

EnthusiastJoined Jan 3, '12From Philadelphia, PACurrentlyOfflineReputation:1(100%)

6th Generation Celica › Engine/Transmission/Maintenance

i'll try exhaust wrap. thanks.

Topic ID: 87897 • Post ID: 9768564

any temporary fixes to make an exhaust leak sound better? - 6G Celicas Forums

EnthusiastJoined Jan 3, '12From Philadelphia, PACurrentlyOfflineReputation:1(100%)

6th Generation Celica › Engine/Transmission/Maintenance

do our stock mufflers just unbolt? what's your guys opinions on taking the muffler off?

Topic ID: 87897 • Post ID: 9768560

any temporary fixes to make an exhaust leak sound better? - 6G Celicas Forums

EnthusiastJoined Jan 3, '12From Philadelphia, PACurrentlyOfflineReputation:1(100%)

6th Generation Celica › Engine/Transmission/Maintenance

my whole flex pipe is broken & my car sounds like sh*t.
im eventually getting custom header-back exhaust but is there anything i can do right now to make it sound better?
This post has been edited by
...

Topic ID: 87897 • Post ID: 9768556

FS: left over parts after gt-four front conversion - 6G Celicas Forums

EnthusiastJoined Jan 3, '12From Philadelphia, PACurrentlyOfflineReputation:1(100%)

6th Generation Celica › Buying/Selling

sorry for not getting back to anyone i havent been active on here i've been really busy with work & such. i'd like to finally get rid of these parts though. i still have everything pictured. just let ...

Topic ID: 87307 • Post ID: 9763312

FS: left over parts after gt-four front conversion - 6G Celicas Forums

EnthusiastJoined Jan 3, '12From Philadelphia, PACurrentlyOfflineReputation:1(100%)

6th Generation Celica › Buying/Selling

QUOTE (Tigawoods @ Aug 28, 2012 - 2:06 PM)
curious how much are you looking to get for the hood
i'm not quite sure how much they go for? i'd figure around $200.

Topic ID: 87307 • Post ID: 9763308

FS: left over parts after gt-four front conversion - 6G Celicas Forums

EnthusiastJoined Jan 3, '12From Philadelphia, PACurrentlyOfflineReputation:1(100%)

6th Generation Celica › Buying/Selling

Hood
almost perfect condition.
Passenger/right side fender
there's a scuff below the parking light near the bottom of the fender, but other then that it's in good condition.
Turn signal lights.
decent...

Topic ID: 87307 • Post ID: 9763306

Ant's 95 GT project - 6G Celicas Forums

EnthusiastJoined Jan 3, '12From Philadelphia, PACurrentlyOfflineReputation:1(100%)

6th Generation Celica › My Project

teaser

Topic ID: 85195 • Post ID: 9682483

Ant's 95 GT project - 6G Celicas Forums

EnthusiastJoined Jan 3, '12From Philadelphia, PACurrentlyOfflineReputation:1(100%)

6th Generation Celica › My Project

not yet tiga, we got the 5s out. just put in new timing belt, water pump, & thermostat in the beams. we need to rip apart both trans still & take the 3s flywheel & pressure plate & put them in my tran...

Topic ID: 85195 • Post ID: 9682482

Ant's 95 GT project - 6G Celicas Forums

EnthusiastJoined Jan 3, '12From Philadelphia, PACurrentlyOfflineReputation:1(100%)

6th Generation Celica › My Project

Very good info richee thanks again, but i've found where to get most of the parts & such already. i think i've read just about every thread on 6gc related to the beams.
& yes i will get a picture of t...

Topic ID: 85195 • Post ID: 9682479

Ant's 95 GT project - 6G Celicas Forums

EnthusiastJoined Jan 3, '12From Philadelphia, PACurrentlyOfflineReputation:1(100%)

6th Generation Celica › My Project

here's another pic of the engine as it sits.(phone quality, will make sure to take my camera from now on!) it needs a power wash.
& we are going to re-paint the valve cover & intake manifold. so far f...

Topic ID: 85195 • Post ID: 9682477

Ant's 95 GT project - 6G Celicas Forums

EnthusiastJoined Jan 3, '12From Philadelphia, PACurrentlyOfflineReputation:1(100%)

6th Generation Celica › My Project

i'd say maybe a month or two. i located a b-pipe. still need oem intake, maf, timing belt, water pump, thermostat...etc. we're gonna check out the flywheel & pressure plate on the trans that's on the ...

Topic ID: 85195 • Post ID: 9682476

Ant's 95 GT project - 6G Celicas Forums

EnthusiastJoined Jan 3, '12From Philadelphia, PACurrentlyOfflineReputation:1(100%)

6th Generation Celica › My Project

QUOTE (lagos @ Feb 26, 2013 - 8:44 PM)
Cool project. Who is doing the body work? I have a fender that needs to be painted if you have any hookups!
my father & I have done everything ourselves so far e...

Topic ID: 85195 • Post ID: 9682473

Ant's 95 GT project - 6G Celicas Forums

EnthusiastJoined Jan 3, '12From Philadelphia, PACurrentlyOfflineReputation:1(100%)

6th Generation Celica › My Project

on the way home with a BEAMS!!!!!!!!!!

Topic ID: 85195 • Post ID: 9682470

Ant's 95 GT project - 6G Celicas Forums

EnthusiastJoined Jan 3, '12From Philadelphia, PACurrentlyOfflineReputation:1(100%)

6th Generation Celica › My Project

Topic ID: 85195 • Post ID: 9682468

Ant's 95 GT project - 6G Celicas Forums

EnthusiastJoined Jan 3, '12From Philadelphia, PACurrentlyOfflineReputation:1(100%)

6th Generation Celica › My Project

half of the celica emblem came off when i was washing it, so i debadged it.
should be getting a new timing belt, valve cover gasket, spark plugs & wires, & water pump next week. so finally i can start...

Topic ID: 85195 • Post ID: 9682467

Ant's 95 GT project - 6G Celicas Forums

EnthusiastJoined Jan 3, '12From Philadelphia, PACurrentlyOfflineReputation:1(100%)

6th Generation Celica › My Project

Topic ID: 85195 • Post ID: 9682463

Ant's 95 GT project - 6G Celicas Forums

EnthusiastJoined Jan 3, '12From Philadelphia, PACurrentlyOfflineReputation:1(100%)

6th Generation Celica › My Project

working on it guys! we just put a new axle in on the driver's side. gotta do the timing belt, valve cover seal, & exhaust before the paint job. you can't say she looks bad though.

Topic ID: 85195 • Post ID: 9682460