doGGy

#1

ok, i just got my apexi s-afc, and where is no 7a-fe instaliation diagram and where is no such engine in instruktion and etc. Where to find how to conect, and how to set this thing to my engine! Any comments are welcome!

Thanks.

Romka

---

Ex celica owner - just a guy from other side of the pond...Full custom Projects from restoration to performance builds<<<<<< DCw / JDMart >>>>>>>

edo17982

#2

I finished to connect it yesterday.
Follow the scheme T4B that's the same of our engine >> >>

Edo

Silver94CelicaOwner

#3

Let us all know how well they work once theyre installed >>

---

3rd gen ST205 3SGTE - Alive and boosting.

edo17982

#4

When I'll have some time I'll write an how to >>

hiflytsi

#5

Here it is for the GT, maybe it will give you some kind of guide.

doGGy

#6

Thaks guys, i will try to cennect it this weekend. I will let you know hoe it works >>

---

Ex celica owner - just a guy from other side of the pond...Full custom Projects from restoration to performance builds<<<<<< DCw / JDMart >>>>>>>

doGGy

#7

Another question. Maybe somone has a good S-AFC set up for the ST with filter/exhaust??? Or just the example of how the S-AFC has to be tuned?

---

Ex celica owner - just a guy from other side of the pond...Full custom Projects from restoration to performance builds<<<<<< DCw / JDMart >>>>>>>

edo17982

#8

When I'll have my head remounted I'll try some configs and I'll let you know....but I think it'll take a quite long time to complain....

doGGy

#9

--edo17982+Apr 24, 2003 - 3:41 AM

QUOTE (edo17982 @ Apr 24, 2003 - 3:41 AM)

When I'll have my head remounted I'll try some configs and I'll let you know....but I think it'll take a quite long time to complain....

what would be good

---

Ex celica owner - just a guy from other side of the pond...Full custom Projects from restoration to performance builds<<<<<< DCw / JDMart >>>>>>>

Drunken_Style

#10

You have to have the s-afc dyno tuned to get the most out of it. Plus any new performance parts that you add you will need to have it retuned to maximize performance. Hope this helps.

---

Black 1996 Celica GT ConvertibleFor SaleAlpine Silver Lexus GS300

west_minist

#11

hey doggy!

Did you sent me a message today?

If so, i just finish install the Nology M80 coil on the car. Instant leanest.

I did a little test an was staying the car is not rev or pulling as hard with the old coil. I also notice no back firing.

When I got home and adjust the fuel/air ratio, I was lean. Not lean lean, but at the point of saving gas.

I have reture to run a tab rich. Will see how the car feels tomorrow.

But just starting the car and moving of, the torque is very noticeable.

I did not had chance to look for the diagram. Did you call Apexi?

Is the 4AFE pin out the same as the 7AFE anyone?

edo17982

#12

yeas West, it's the same.
I wrote yestersay the How-to and I hope Coomer will release it soon >> >> >> >>

Why don't u write an how-to for the M80 coil since we've the coil in the distributor >>

This post has been edited by edo17982: Apr 25, 2003 - 6:44 AM

doGGy

#13

Hey,
It is done! Installed it this weekend. And it wasnt really hard job (took me an hour to install it). Work perfectly, looks awsome! Thanks to edo17982, Charlie97L and west_minist for helping me out with wiring and etc. >>

---

Ex celica owner - just a guy from other side of the pond...Full custom Projects from restoration to performance builds<<<<<< DCw / JDMart >>>>>>>

edo17982

#14

I'm happy for you man! >> >> >> >>
Check the How to article I wrote and tell me if it sounds clear for the installation! >> >> >> >>
If needs, leave a comment

Drunken_Style

#15

Looks great man.

---

Black 1996 Celica GT ConvertibleFor SaleAlpine Silver Lexus GS300

maikl

#16

can anyone know how can i install it to my car? an ss-iii vvt-i?

seth042280

#17

anyone know where the cheapest place to get this is ?

edo17982

#18

Ebay

edo17982

#19

--maikl+Apr 28, 2003 - 5:35 AM

QUOTE (maikl @ Apr 28, 2003 - 5:35 AM)

can anyone know how can i install it to my car? an ss-iii vvt-i?

If you get your ECU pinout I'll tell you how to do it. >>

Unknown User

#20

dang doggy that looks nice. i just need somewhere to put that and the avc-r

west_minist

#21

--maikl+Apr 28, 2003 - 7:35 AM

QUOTE (maikl @ Apr 28, 2003 - 7:35 AM)

can anyone know how can i install it to my car? an ss-iii vvt-i?

The 3sge info is there for you. vvti does not make a different.

That only comes into play when change your ecu.

---

West_MinistHydra EMS Dealer & TunerSubaru ECUFlash Tunerhttp://www.socob.bbhttp://xtremeracingtuning.comViciously Tuned, Driven Hard

west_minist

#22

--doGGy+Apr 28, 2003 - 1:48 AM

QUOTE (doGGy @ Apr 28, 2003 - 1:48 AM)

Hey, It is done! Installed it this weekend. And it wasnt really hard job (took me an hour to install it). Work perfectly, looks awsome! Thanks to edo17982, Charlie97L and west_minist for helping me out with wiring and etc. >>

Well done.

Did you use the 4AFE wiring to work with the 7AFE?

I am sorry that I did not get a chance to really help you.

I have been busy at work all week and now have a big presentation coming up this week which I needed to finish.

If you like, just do a how to on 6gc.net for anything special that you hdad to do for the 7afe.

---

West_MinistHydra EMS Dealer & TunerSubaru ECUFlash Tunerhttp://www.socob.bbhttp://xtremeracingtuning.comViciously Tuned, Driven Hard

edo17982

#23

--west_minist+Apr 28, 2003 - 7:23 AM

QUOTE (west_minist @ Apr 28, 2003 - 7:23 AM)

--doGGy+Apr 28, 2003 - 1:48 AM QUOTE (doGGy @ Apr 28, 2003 - 1:48 AM) Hey, It is done! Installed it this weekend. And it wasnt really hard job (took me an hour to install it). Work perfectly, looks awsome! Thanks to edo17982, Charlie97L and west_minist for helping me out with wiring and etc.  >> Well done. Did you use the 4AFE wiring to work with the 7AFE? I am sorry that I did not get a chance to really help you. I have been busy at work all week and now have a big presentation coming up this week which I needed to finish. If you like, just do a how to on 6gc.net for anything special that you hdad to do for the 7afe.

I already posted an how to, West....check for it >> >> >>

This post has been edited by edo17982: Apr 28, 2003 - 10:14 AM

west_minist

#24

--edo17982+Apr 25, 2003 - 5:56 AM

QUOTE (edo17982 @ Apr 25, 2003 - 5:56 AM)

yeas West, it's the same. I wrote yestersay the How-to and I hope Coomer will release it soon >> >> >> >> Why don't u write an how-to for the M80 coil since we've the coil in the distributor >>

My car is a subaru.

Install is easy in your car.

Once you have the head, you will get it do.

Now in theory (what I would do if I had it builtin), I would strip the distributor down, and get the wires running to the input side of the internal coil.

I would either replace those replace those wires with longer ons or pull them out of the loom to where my new nology coil is.

I would then run a low resistance spark plug wire from my coil to the inside of the distributor unit to the point head.

I must warn you the M80 is a racing coil that must be use with Either a CRANECAMS HI6/7 oe MSD Digital 6 or 7. That coil that you can use is the M60.

If you want, you can replace your distributor with a MSD one.

---

West_MinistHydra EMS Dealer & TunerSubaru ECUFlash Tunerhttp://www.socob.bbhttp://xtremeracingtuning.comViciously Tuned, Driven Hard

edo17982

#25

With an MSD one? which one? I checked on their site on section"imports" but nothing found for my application....can you help me? >>

west_minist

#26

--edo17982+Apr 25, 2003 - 5:56 AM

QUOTE (edo17982 @ Apr 25, 2003 - 5:56 AM)

yeas West, it's the same. I wrote yestersay the How-to and I hope Coomer will release it soon >> >> >> >> Why don't u write an how-to for the M80 coil since we've the coil in the distributor >>

Hi edo!

Do you have if you start to tune, start of rich and use the ieither the built in a/f gauge or an external one.

Also keep and eye on engine temperature and pinging.

---

West_MinistHydra EMS Dealer & TunerSubaru ECUFlash Tunerhttp://www.socob.bbhttp://xtremeracingtuning.comViciously Tuned, Driven Hard

edo17982

#27

I have the Autometer A/f gauge.....
But....the how can the AFC read the A/f ratio if it don't use the oxygen sensor signal?? >>
Also....there is not a modalityu to visualize the a/f ratio into it....

This post has been edited by edo17982: Apr 28, 2003 - 10:24 AM

west_minist

#28

Ok. I was told that it has one.

I never really research the safc due to the fact my final alternative was a new computer.

Ok. Use the autometer.

<<<<Also....there is not a modalityu to visualize the a/f ratio into it....>>>>
I do not understand the line above!

edo17982

#29

I don't think that the AFC can visualize A/f ratio....that's the way I'm using the autometer gauge

west_minist

#30

--edo17982+Apr 28, 2003 - 9:32 AM

QUOTE (edo17982 @ Apr 28, 2003 - 9:32 AM)

With an MSD one? which one? I checked on their site on section"imports" but nothing found for my application....can you help me? >>

Ok. Sometimes you have to call them or send dimensions to them.