i like that TRD badge.
Post your cooling plate Picture - 6G Celicas Forums
looks good. nice addition to your clean engine bay.
This post has been edited by j0e_p3t: May 13, 2007 - 6:18 PM
This post has been edited by j0e_p3t: May 13, 2007 - 6:18 PM
ss-iii splitters and 404 skirts areon. which means i need to update my sig.
>
is that a bottle of water up there?
QUOTE(Batman722 @ May 13, 2007 - 7:05 PM) [snapback]557183[/snapback]
>
is that a bottle of water up there?
>
actually yes, I get very thirsty sometimes.
J/K, it's just the bottle cut in half. With the J-Speed 3 point strut bar it's kinda hard to add oil because it's in the way, so I keep that there just in case
QUOTE(DSToyo @ May 13, 2007 - 8:01 PM) [snapback]557202[/snapback]
>
is that a bottle of water up there?
is that a bottle of water up there?
actually yes, I get very thirsty sometimes.
J/K, it's just the bottle cut in half. With the J-Speed 3 point strut bar it's kinda hard to add oil because it's in the way, so I keep that there just in case
my st205 swapandour Beams swap
you used a different decal other than one of mine, how dare u!
Did any of you guys have trouble closing the hood when you put the hood stand down and over the cooling plate? I hope that makes sense. I basically coulnt close my hood cause the stand was on the cooling plate. Anyone have the same problem? and remedies?
thanks http://i194.photobucket.com/albums/z51/egg...uiredTools1.jpg
This post has been edited by eggman40: Jun 17, 2007 - 4:12 PM
thanks http://i194.photobucket.com/albums/z51/egg...uiredTools1.jpg
This post has been edited by eggman40: Jun 17, 2007 - 4:12 PM
>
everyone should have gone through that, I'll see If I can take a pic tomorrow of how I close mine.
QUOTE(eggman40 @ May 13, 2007 - 9:14 PM) [snapback]557252[/snapback]
>
Did any of you guys have trouble closing the hood when you put the hood stand down and over the cooling plate? I hope that makes sense. I basically coulnt close my hood cause the stand was on the cooling plate. Anyone have the same problem? and remedies?
thanks
Did any of you guys have trouble closing the hood when you put the hood stand down and over the cooling plate? I hope that makes sense. I basically coulnt close my hood cause the stand was on the cooling plate. Anyone have the same problem? and remedies?
thanks
everyone should have gone through that, I'll see If I can take a pic tomorrow of how I close mine.
>
Sweet! thanks. My solution when i have to money is to see if i could custom fit a set of tein hood dampers and get rid of the stand alltogether. But yea i dont have it mounted at the moment so if you have a pic help me out. Thanks!
QUOTE(Culpable04 @ May 13, 2007 - 8:50 PM) [snapback]557283[/snapback]
> >
everyone should have gone through that, I'll see If I can take a pic tomorrow of how I close mine.
QUOTE(eggman40 @ May 13, 2007 - 9:14 PM) [snapback]557252[/snapback]
>
everyone should have gone through that, I'll see If I can take a pic tomorrow of how I close mine.
Sweet! thanks. My solution when i have to money is to see if i could custom fit a set of tein hood dampers and get rid of the stand alltogether. But yea i dont have it mounted at the moment so if you have a pic help me out. Thanks!
Mine...
1994 JDM GT4 WRC
My C-One bought here on the forum.
'94 ST202 - tuned, highly apprieciated, but sold.'99 ST205 - imported, legalized, Stage 1 completed.For slow driving: Yamaha XVS650 Drag Star.The most recent addition to the family and for the family: Toyota RAV4 2.0 VVTiCelica-ClubPoland-Everything you want to know about your favourite car ... in Polish
Got mine from doGGy...
>
x2, how are you all closing the hood with the hood stand?
QUOTE(eggman40 @ May 13, 2007 - 10:14 PM) [snapback]557252[/snapback]
>
Did any of you guys have trouble closing the hood when you put the hood stand down and over the cooling plate? I hope that makes sense. I basically coulnt close my hood cause the stand was on the cooling plate. Anyone have the same problem? and remedies?
thanks
Did any of you guys have trouble closing the hood when you put the hood stand down and over the cooling plate? I hope that makes sense. I basically coulnt close my hood cause the stand was on the cooling plate. Anyone have the same problem? and remedies?
thanks
x2, how are you all closing the hood with the hood stand?
>
I just removed the hood stand and keep it in the trunk. That's my solution for now until someone does a how-to on the hood dampers.
QUOTE(DSToyo @ May 20, 2007 - 2:07 AM) [snapback]559567[/snapback]
>
>
x2, how are you all closing the hood with the hood stand?
>
QUOTE(eggman40 @ May 13, 2007 - 10:14 PM) [snapback]557252[/snapback]
>
Did any of you guys have trouble closing the hood when you put the hood stand down and over the cooling plate? I hope that makes sense. I basically coulnt close my hood cause the stand was on the cooling plate. Anyone have the same problem? and remedies?
thanks
Did any of you guys have trouble closing the hood when you put the hood stand down and over the cooling plate? I hope that makes sense. I basically coulnt close my hood cause the stand was on the cooling plate. Anyone have the same problem? and remedies?
thanks
x2, how are you all closing the hood with the hood stand?
I just removed the hood stand and keep it in the trunk. That's my solution for now until someone does a how-to on the hood dampers.
"Remember, amateurs built the ark and professionals built the Titanic. Butrevolutionariesbuilt the Celica!"- Me
>
LOL!
the shocker though!
QUOTE(bojangles_8686 @ May 17, 2007 - 7:30 AM) [snapback]558836[/snapback]
> Got mine from doGGy...
LOL!
the shocker though!
I'll take a picture with my phone on lunch time to show you guys how to close it.
I haven't taken the pic for lack of a digi cam so I guess cell will do it.
I haven't taken the pic for lack of a digi cam so I guess cell will do it.
>
any update on this?.....
QUOTE(Culpable04 @ Jun 6, 2007 - 7:37 AM) [snapback]565496[/snapback]
>
I'll take a picture with my phone on lunch time to show you guys how to close it.
I haven't taken the pic for lack of a digi cam so I guess cell will do it.
I'll take a picture with my phone on lunch time to show you guys how to close it.
I haven't taken the pic for lack of a digi cam so I guess cell will do it.
any update on this?.....
any1????
sorry I haven't post it yet, but my digital cam is far from home and I can't find the cable for my video cam. as soon as I find it I'll post a little video for it. I did take a small video with my phone but is not clear enough so I didn't post it.
my st205 swapandour Beams swap
you dare get a sticker without going through me!
do any of your guys have an issue with the Hood stand not letting the hood close? and what did you guys do to get rid of the problem?
>
the hood stand still fits, it just does't go into the plastic clip. but hood closes just fine.
QUOTE(eggman40 @ Dec 5, 2007 - 1:25 PM) [snapback]619929[/snapback]
>
do any of your guys have an issue with the Hood stand not letting the hood close? and what did you guys do to get rid of the problem?
do any of your guys have an issue with the Hood stand not letting the hood close? and what did you guys do to get rid of the problem?
the hood stand still fits, it just does't go into the plastic clip. but hood closes just fine.
>
I removed the hood stand and keep it in the trunk.
QUOTE(eggman40 @ Dec 5, 2007 - 8:25 PM) [snapback]619929[/snapback]
>
do any of your guys have an issue with the Hood stand not letting the hood close? and what did you guys do to get rid of the problem?
do any of your guys have an issue with the Hood stand not letting the hood close? and what did you guys do to get rid of the problem?
I removed the hood stand and keep it in the trunk.
"Remember, amateurs built the ark and professionals built the Titanic. Butrevolutionariesbuilt the Celica!"- Me
culp did u ever take a pic with this new set of people getting there cooling plates we shoudl know how to fix it
not to knock on anyone, but i think when you are putting this on that you should touch the 2 radiator support bolts up, and your hood latch & release up with some paint... hide the rust. shame to see such a beautiful engine bay have minor imperfections.
lookin good though!
lookin good though!
you know why they put sheep at the edge of a cliff.... that way they push back!(2:27:32 AM) edit: please f*cking work, f*ck, sh*t, piss(2:28:08 AM) edit: that did the trick
kinda dark, but it's finally painted
edit: Culp, did you ever get around to taking a pic of how the prop should be?
This post has been edited by 96bluevert: Mar 4, 2008 - 4:46 PM
"A true car enthusiast can see the potential in any car"QUOTE (njccmd2002 @ Oct 3, 2008 - 2:01 PM)i rather be a slow turtle in risk of extinction, than a fast locust, that you can see everywhere and need to be terminated.
the prop just snug fit in place
^^^ looks how I was thinking it would fit. Just wanted to makes sure..thanks
"A true car enthusiast can see the potential in any car"QUOTE (njccmd2002 @ Oct 3, 2008 - 2:01 PM)i rather be a slow turtle in risk of extinction, than a fast locust, that you can see everywhere and need to be terminated.
so who here makes these? price? can we get a discount on the c-one items through the forum?
ST205 Group A Rallye GT-Four, #61 of 77............600hp GT3582rGRX133 Toyota Mark X 350s
Are those the same as these that come in stock RAV4's?
