yea it did but i only had one can to work with...it was kind of just a test run, im gonna spray another 2-3 cans on it and do it again just to make sure i get all the crud out of there then hopefully i can paint it

couple more pics...FINALLY got my camera working again soo here we go...












LOL^

when are you putting in the engine?

as soon as i get some more $$$....i still need various parts so i am currently unemployed...i go back to school tomorrow and i will be starting a job there hopefully within the first week or 2, then i will be able to get the other crap i need....wireing harness, axles, fuel pump, shifter cables, t-belt, water pump and a rebuild kit for the motor...hopefully its ready befor next spring but we'll see

hey would i be able to install a 3sgte engine in my 1999 toyota celica gt but the only problem its automatic?? or a Mr2 turbo engine?

>

absoutly...you got a leg up on me even...i wish my car was a Gt caus its so much easier..you dont need axles, shifter cables (even though yours is auto) or motor mounts....yours basically bolts right up...if i were you i would swap out the auto for a stick..it would be so much better

yea im thinking of doing that bc i found a website where the sell u the engine with everything the ecu and the tranny so ima switch of the auto for stick... but im happy bc now i will be able to swap my 5sgte for a 3sgte engine right?? but my only problem will be smog check in cali? any ideas on wat i can do to pass the smog test?

honestly i dont live in cali so i dont know that you would have to do to pass smog out there...im assuming your going to need all cats and a well rounded car that will pass inspection...philly and LA are like night and day...lol

HEY MAN are you rolling your car around without the halfshafts in the axel hubs? The bearing NEEDS the halfshaft in there for support; the weight will crush your bearing. they will need to be replaced soon if not . Ive seen it happen more than once. So hack up 2 old ones and shove em in there if you are going to put the cars weight on the front tires. Thought you should know!!!!

Kyle

i'm really excited to see this thread keep going. It helps with all the pictures too. Once i get a good job going and i got the money. I'm going to just buy the engine first and rebuild it then put her in.

yea me 2 hey thanks for the info im really looking forward to swap my engine oh and ima convert my car to stick im running auto right now but now since im getting a new engine ima get a manual tranny!

pushed it out front today and decided to paint the bay...im not one for dirty, ugly looking engine bays so i ran to pepboys, got some 2 inch masking tape, 2 cans of Gunk, and picked up a 50 piece ratchet set for $13 bucks!!...anyway....pics speak for themself...

gunked and pressure washed




scuffed/sanded




Preped and taped






Sprayin...




and done..


I tried to take a good picture of the paint to give yous an idea of what it looks like but the sun was just to bright and it was shining right on it..this on didnt turn out to bad...its like a dark electric blue effect


















now this is left over paint from when my step-dad painted the car back in like 03/04 so it is single stage...meaning that it has clear already mixed into the paint...i am going to see how it looks tomorrow because i left everything taped up and if it dulls any then i am going to shoot a couple coats of clear on it...it looks pretty good thoguh and i went back out about an hour and a half later...the paint still looked wet but it was completely dry so i think the single stage will work well with the bay...next is the rebuild kit for the motor and the wireing harness...i finally got my @ss a job so it should be comming together rather nicely these next coulple of weeks

This post has been edited by 95st-celica: Sep 21, 2008 - 3:21 PM

I bet the pics don't do it justice, nice job !

>

thanks man...it does look good in person...im diggin it

next is adding a little finishing touches to it...muhaha

This post has been edited by 95st-celica: Sep 21, 2008 - 2:17 AM

just read this thread from start and absolutely great job so far keep up the good work

The bay turned out really well!

Awesome job on the bay! Thanks for the update, i look forward to seeing more in the coming weeks.

Nice bro - good to see someone taking the time to do the little things to make it that much better. Gonna be well worth it when it's all done.

>

yes it will...the >>little>> things make all the >>DIFFERENCE>> lol

Props to pops....









some guy gave it to him...its kinda like the neon bar so i'll have to see if i can make it fit...might nit clear my brake fluid tank though...i'll either use this one or my neon bar untill i can afford a good cusco J-speed, or TRD 3 point strut bar...but for free im not complaning

This post has been edited by 95st-celica: Sep 22, 2008 - 6:07 PM

well...just a little update...i got a bunch of parts for the 3s about a month or so ago...taking my time putting them in because it's cold out and i still dont have a license...timeing belt, all gaskets, front and rear main seals, cam seals, cap, rotor, etc....i picked up a full black leather interior for it, and i also picked up a can of VHT night shade tailight/headlight tint...i was bored the other day so i figured i would black out the tails...heres the result















and my poor car about 2 months ago

another little update...i picked up a full Black leather interior for the car a while ago...finally decided to clean it up and throw it in...sooo much nicer in my oppinion..now the interior is almost all black with the exception of the headliner...i'll eventually get to that..i installed a short throw shifter which im having some problems with it hitting my e-brake...i have a couple of options as far as that goes so i'll figure it out..and just a couple random pictures of other goodies i have for it



From This:




To This:













^Not Good...i'll have to work on that^



And 2 pictures of the custom camera bar i made




Goodies










Seats are sooo comfortable...probably the most comfortable stock seats other then srt-4 seats...these hug you really well yet arent too much...the box of parts is for the 3s...i have a few more things comming for it and waiting on my wireing harness then thats going in...i also just picked up a loteck 3 gauge A-pillar Pod...thats on its way...its comming together....slowly but surely

This post has been edited by 95st-celica: Dec 29, 2008 - 8:49 PM

Clean those seats a bit! But they look good. I wouldn't mind leather, since my interior still looks pretty damn clean and new...if I had a black headliner and some nice leather seats, it'd be baller. And a stick, while I'm at it...

This post has been edited by RickJamesBish: Dec 29, 2008 - 5:30 PM

alright guys...its been a while and i have been gathering a lot of $hit together..trying to get this thing in before summer...i drove out past harrisburg a couple weeks ago and picked up my shifter cables, and my motor mount that i needed and also came home with another goodie..enjoy...expect another big update this weekend...if the weather gods are on my side she should be bolted up and almost done

new walbro 255 and my polly-urathane motor mount inserts



2 new axles


My front mount that came today


3 post i picked up


my work in progress CC


and my other work in progress



still waiting on all my intercooler pipeing (which should be here tomorrow or the next day), my oil pressure gauge, and some leds to finish up the climate control.

This post has been edited by 95st-celica: Mar 31, 2009 - 7:02 PM

Good job dude..

thanks homie....arent ST's fun? haha i could kill myself

This post has been edited by 95st-celica: Apr 1, 2009 - 12:31 PM

THAT LOOKS FREAKEN BAD ASS!!!! now show us some engine pictures!!!! gratz and props on all the work

Joe, that is a NEW carquest axle. Not a rebuild. Nice job. Hopefully we can make some progress this weekend.

dude your car looks sweet how did you do that to the ac dials and gauges with the leds, did you use trojans...or leds..lol....??? your car is gonna look sweet man....admire that..

Thanks guys




yea i was lookin at the box earlier and it does say new its just the sticker is ripped off...but the one from pep boys defentially looks brand new..so its cool i got 2 new axels...i wanna find my stock one and see if these are thicker caus they do look like it. sunny and 60 supposidly saterday....
>

This post has been edited by 95st-celica: Apr 1, 2009 - 1:35 AM

motor is in (kind of)....i still have to drill out the hole a little bit more on the pass. side for the motor mount. i am going to be using threaded rod with 2 washers and 2 nuts for the mount. my problem is that under the frame it has a little bit of a lip to it and you cant fit a washer on there, so i have to grind it down so the washer will fit flush. i just droped the crossmember and hopefully i can sneak the motor in a little better now..the trans was hitting the steering rack and the crank pully was hitting the frame which was f-in everything up. now that i have a little more room to work with i can drop the motor all the way down then pull it back up into place. it looks like its gonna rain here tonight and maybe into tomorrow so im trying to get this thing bolted up asap so i can push it back under the car port. i'll keep it updated

(when your motor is hangin from a riged ass set-up and your under there workin, you want some insurance, hence the board) just so i dont get any dumb questions






This post has been edited by 95st-celica: Apr 10, 2009 - 6:51 PM