Soulend

#1

Hey everyone,

I finally got my 3SGTE engine and am finding my self both excited and over whelmed. I don't know much about cars, but I'm wanting to work and learn for this beautiful car. so I'll post pictures and questions about the process. so with out further adu...

3SGTE Swap Pictures

Tell me your opinions, and what to look out for!

Thanks,
Soul

Smaay

#2

i hope you didnt pay too much for that. it looks pretty rough and beat up

---

2001 Celica GT-S Turbo1997 Supra TT 6speed1997 Celica 3MZ/1MZ swap1990 Celica All-Trac

Soulend

#3

I didn't pay to much no... under 2K. besides rust on things i plan to replace, plastic and tubes are things I'm not to worried about. I'm in constant communication with the seller who, so far seems willing to help with replacing parts. my friend is going to let me borrow an engine stand so I can comb over the engine.

Soul

This post has been edited by Soulend: Apr 25, 2010 - 12:07 PM

Smaay

#4

i recommend tearing the engine down and doing a full refresh. look ay mt 7A-FE rebuild thread. lots of pictures and details.

This post has been edited by Smaay: Apr 25, 2010 - 11:02 AM

---

2001 Celica GT-S Turbo1997 Supra TT 6speed1997 Celica 3MZ/1MZ swap1990 Celica All-Trac

Soulend

#5

hey everyone,

can someone tell me what this is?

Broken Part

Thanks,

Soul

Remy

#6

Thats the PCV valve.

---

"To Protect And To Serve The Wealthy" -POLICE

kavy

#7

that seems to happen often.i went thorough the same.try looking for a gen 2 3sge PCV valve.its fully metal.a bit longer in length but stronger and it does the job.

Soulend

#8

okay cool guys thanks!

Soul

Soulend

#9

Behold! the rebuilt Turbo!





The guys at AZ Turbo did an amazing job. and only for $200!

next is replacing the timing belt (yay fun!) the putting it all back together.

A few questions though, Since this is going into an ST I know I have to replace the engine mount. do I also have to replace:
accel cable?
Shifter cables? (one guide mentioned this)
CV Half shafts?
also should (have to?) I use a 5S-FE clutch and pressure plate?

what Gauges do you recommend for this swap? IE Boost guage, Oil pressure guage...

Soul

This post has been edited by Soulend: Jul 25, 2011 - 6:31 PM

Stambo

#10

yea i'm half way through the process of swapping a 3sgte into my st.

You need the shifter cables for sure, gt tranny, throttle cable. The rear trans mount off your old st trans will work with the gt trans. You just have to get ahold of the right bracket that mounts onto the transmission.

You gotta get new axles for sure too. Just get the gt axles and your good to go. As far as the 5s-fe clutch and pressure plate, dr. tweak sells a good clutch that fits perfect on the 5s tranny. You just gotta use a 3s flywheel.

---

2nd Gen 3s-gte.... It lives!97celiman"92-gt-quit making up random acronyms that dont mean anything. the only real acronym is JDM"

Soulend

#11

Thanks for the info Stambo, Maybe you could help me out here and there.

Also does anyone know where I can get a Crankshaft seal?

This post has been edited by Soulend: Oct 3, 2010 - 12:05 AM

Soulend

#12

okay! an update,

so I have pretty much every part I need (minus a inter-cooler reservoir, but I can pick that up locally) just got an update with the Wiring harness I sent to Tweak'd should be getting that back soon, and practically everything is back on the engine.

I'm seriously excited about finally getting this thing in the car. bad news, which some of you might know, the 1.8 in the car just finally gave out a couple weeks ago. I've had to let it sit for a bit, but this week I'll be tearing it down and get it ready to tow up to Phoenix where I can get more help from some friends and the extra tools Ill need to get it in and such...

now that I am about to finally put the engine in the car, what should I look out for?
what vacuum lines, on the car can I use?

any last minute advice?

Thanks
Kevin

Johnnyny

#13

can you give me more specs on the rebuilt turbo?

Soulend

#14

hey everyone,

I got my wiring harness back from Tweak'd and man am I impressed! thanks to everyone over there for helping me out with this!

this weekend I am going to try and get the engine in, and running. I'm really needing the support, and prayers that can be offered haha. I'm absolutely sure the engine will run, but I just hope I'm not missing something small.

I will admit this is the first time I've done something like this, so I'm expecting little annoyances to pop up as I run through it.

Thanks for the help I've been getting, and I hope you guys can help somemore!

Kevin

This post has been edited by Soulend: Jul 25, 2011 - 6:32 PM

Soulend

#15

Moved my Celica from here:

to here:


Ill head up to my friends house Thursday night and start work on the car... hopefully I can get it done by Sunday.

wish me luck

Kevin

This post has been edited by Soulend: Jul 25, 2011 - 6:33 PM

Bigblock

#16

Sounds like you have your hands full!!
Yup, I wish you luck!!!!

Since it's cooled down from 100's to the 99's ( haha )
I hope some of your friends are willing to help---

Soulend

#17

heh yeah its been hot, part of the reason why it is taking so long, my friend cant handle the heat sometimes, so his project car is taking a bit longer so he had to finally move his out of the way so i can work on mine. he, and when my other friend (owns the Taco) is out of work are both willing to help... Tomorrow, Ill try to get the beat up 4AFE (poor thing) out and clean the engine bay while my friends are at work. then when able try and get the engine Friday and Saturday... If its done and in saturday, Ill try and get the exhaust put on, or I'm towing it home Sunday :\

all and all its going to be a lot of work!

Kevin

presure2

#18

good luck bro!

---

Former Team 5SFTE pro member ;)13.6@108MPH, 5SFTE Powered

mak5603

#19

>

QUOTE (presure2 @ Oct 14, 2010 - 7:52 AM)

>good luck bro!

x2

---

2006 BMW 330i - 6 Speed - Dinan Stage 12014 Toyota Rav4 XLE

Soulend

#20

haha thanks guys!

I know this is pretty much a stupid question, but how bad would it be to run the car for a few minutes with just a downpipe?

I'm having a local shop install the new system in for me... they are going to do it for pretty cheap, but they will not just sell me the kit. they want to make it for the car, which is fine. but I probably wont be able to do it till monday or wednesday...

I just to test it, and see if its running okay and take it around the block a couple of times...

mak5603

#21

It will be really, really loud open down pipe.

---

2006 BMW 330i - 6 Speed - Dinan Stage 12014 Toyota Rav4 XLE

Soulend

#22

yeah... haha I will make sure to have earplugs... but really will it damage the engine? like the valves or turbo?

Kevin

Culpable04

#23

the car will be fine, it'll be loud but who cares, enjoy it lol.

some people have driven around for weeks with just downpipe.

mak5603

#24

Yeah, I was going to say, it's Just like the Honda people who drive around open header for the entire existence of their car, haha. Only thing is open header Honda's sound like awful farts and open downpipe just sounds ridiculously badass, like a race car, haha.

---

2006 BMW 330i - 6 Speed - Dinan Stage 12014 Toyota Rav4 XLE

DEATH

#25

>

QUOTE (Culpable04 @ Oct 14, 2010 - 1:37 PM)

>the car will be fine, it'll be loud but who cares, enjoy it lol.

some people have driven around for weeks with just downpipe.

I've done it many times
don't wait for a exhaust to enjoy your work
Hell when I built my 5S-FTE I went around open DP for a week till I could get to the exhaust place.

This post has been edited by DEATH: Oct 14, 2010 - 1:50 PM

---

ENGINE: '93 RC 3S-GTE/WRC CT-20b [18-20PSI]PERF: TRD/HKS/ARP/NGK/MSD/ACT/Blitz/STRI/APEX'i/TwosRus/GReddy/Magnaflo/KOYOSUSP: Tein/Bilstein/SusTech/INT: SS-III SEATS/Toyota Hyper SportsEXT: WRC/TRD/404QUOTE (lagos @ Aug 25, 2010 - 10:13 AM)Its a safety feature so that people like you don't end up killing themselves or everyone around them.Slow down Paul Walker.6GC Chat - Go there: [url="http://www.griffgirl.com/forum/chat/index.php[/url]

presure2

#26

>

QUOTE (Soulend @ Oct 14, 2010 - 1:58 PM)

>haha thanks guys!

I know this is pretty much a stupid question, but how bad would it be to run the car for a few minutes with just a downpipe?

I'm having a local shop install the new system in for me... they are going to do it for pretty cheap, but they will not just sell me the kit. they want to make it for the car, which is fine. but I probably wont be able to do it till monday or wednesday...

I just to test it, and see if its running okay and take it around the block a couple of times...

it'll be fine.
god awefull loud, but fine.

---

Former Team 5SFTE pro member ;)13.6@108MPH, 5SFTE Powered

Soulend

#27

Haha sweet, yeah if I can get it done by Saturday, ill take it up to an exhaust shop and get the work done, other than that it will have to wait till Wednesday when the guy in my town gets the right connections... thanks for all the help...

So I have the engine ready to be pulled when my friend gets home from work tomorrow... then its going to be a long dash through the night. then test it when its done!

Well I can't think of any questions yet but ill post them when thbey come a long.

Thanks for the help
Kevin

Soulend

#28

Hey, actually I totally forgot about spark plugs, is there a set I can get from a local autostore? atleast somethign I can get the car running on until i can order ones from a provider you suggest?

Thanks for your input.

Kevin

Culpable04

#29

NGK BCP7ES

go to your autozone / napa / advance auto parts and get some of these.

Soulend

#30

Culp to the rescue! haha Thanks man..

Okay, workin on the axels finally got the axle nuts to come off, next are the control arms...