Over 1M Posts • 84K Topics • 9K Authors

Home > Topic #75037

This header will fit, right? - 6G Celicas Forums

Topic #75037 12 posts Started by HectortheRican
Tech-Nics
#2
Yes that will fit your ST. The engines are the same...but I'm sure you already knew that wink.gif
samir0189
#3
isnt this the one that ends up like 2 inches short from bolting to the existing flange under the car??
◊◊◊My F/S Thread!◊◊◊QUOTE(14:19:21) Daniel: That was a JDM hole in the side of the box too. There was so much JDM trapped inside that box that they couldn't contain it, so they had to put a JDM hole in the box to let the JDM out.QUOTEFerdi says (11:29)No, it looks like a hooker put her acid vag on your hood. Acid vag = bigger problem than a few dings.
benzo
#4
>
QUOTE (samir0189 @ Jul 19, 2010 - 2:25 PM) *
>isnt this the one that ends up like 2 inches short from bolting to the existing flange under the car??


yup. hes gonna have to weld and or make an extension.
HectortheRican
#5
>
QUOTE (samir0189 @ Jul 19, 2010 - 1:25 PM) *
>isnt this the one that ends up like 2 inches short from bolting to the existing flange under the car??


All the 7a headers do lol. A local exhaust shop will do the job to make it fit for $30.

Thanks guys!

>
QUOTE (Tech-Nics @ Jul 19, 2010 - 1:00 PM) *
>The engines are the same...but I'm sure you already knew that wink.gif

I sense sarcasm, sir. Lol tongue.gif
taking too long to mod since '09June '12 COTM'95 AT200
Cs91
#6
Mine did not fit against the block, because the oil filter was in the way, so i couldn't get the header close enough to the block to get it tight.
cheela
#7
hmm... never heard that happening before. Was yours like that one too? there's a bunch of them on ebay. never really know which is a good one though.
*1997 Celica ST - 3SGE Greytop BEAMS*1977 Celica RA29 - Classic Cruiser*2005 Matrix AWD - dedded but still hanging around like a ghost2019 Rav4 XLE Premium - Sports mode is fun.
Cs91
#8
>
QUOTE (cheela @ Jul 19, 2010 - 4:01 PM) *
>hmm... never heard that happening before. Was yours like that one too? there's a bunch of them on ebay. never really know which is a good one though.

Mine was the JDM racing one
Bitter
#9
you must have gotten a wrong one then or be using a larger/longer than stock filter.
2000 Celica GTS 'slowest gts evar'1998 Mazda 626 FS-DE/CD4-E
rave2n
#10
My ebay headers from Race daddy or some junk like that, bolted right to the block. As said, it was short from the second cat, and had to have it welded. Cost me 75 bucks.

This post has been edited by rave2n: Jul 19, 2010 - 7:52 PM
mgnt232
#11
mine was from race daddy too! but mine was a worse fitment lol.
All the holes on the header to the block were too small, had to drill them out. came out about 8" short from the 2nd cat, and I had to cut off the piece at the very end of the downpipe, because the "in" on the cat is 1.75" and the piece at the end of the headers downpipe is 2". So I had to cut it off to make it sit flush, and just used some cheap exhaust sealer and extended the pipe obviously.
If you do it your self it ends up a $20 project for piping and sealant smile.gif. but it is a pain! so if you have the money go to an exhaust shop, but if not its not tooo hard, just need the time, and I can tell you exactly what I had to do, which save alot! of time.
I've spilt my heart into this car :) And I don't ever plan to stop- 6GC for Life ->Semper Fi<1994 Cupra :p 3sgte1995 Celica ST DD1969 Chevelle SSalllll balls. P2 approved!
youngboy815
#12
>
QUOTE (HectortheRican @ Jul 19, 2010 - 11:37 AM) *
>I know it'll fit my 7A, but it doesn't have the little "will fit Celica" fine print so I just wanna clear it before I spend money on it because that put the 0.01% of doubt in my mind that'll make me uneasy. Thanks guys.

http://cgi.ebay.com/ebaymotors/TOYOTA-CORO...sQ5fAccessories


I think so laugh.gif
Wholesale Louis Vuitton HandbagsLouis Vuitton HandbagsReplica Handbags
← Back to Topics