Over 1M Posts • 84K Topics • 9K Authors

Engine Block?... - 6G Celicas Forums

Topic #75317 17 posts Started by xIIscrapsIIx
I currently have my motor torn down, the number 2 cylinder looks pretty horrid.... Looking at the money aspect would it be cheaper to find a used block that just needs to be honed, or to have the one I have bored and get over sized pistons?... Not looking at the money aspect which would be the better option?

Scraps
if u got no money get a good used block i u do bore it !
>
QUOTE (Johnnyny @ Aug 5, 2010 - 3:15 AM) *
>if u got no money get a good used block i u do bore it !


Money isn't a problem.... I'm just trying to figure out which would be my better route....

Scraps
if money is not an issue, i highly suggest overboring .020. how bad is the cylinder? toyota does have oversized pistons, so if you want to repair the one cylinder you can. but for best results, do all 4.

2001 Celica GT-S Turbo1997 Supra TT 6speed1997 Celica 3MZ/1MZ swap1990 Celica All-Trac
Do you know where I can find the oversized pistons for my 96 7a?

Scraps
>
QUOTE (Smaay @ Aug 5, 2010 - 11:24 AM) *
>if money is not an issue, i highly suggest overboring .020. how bad is the cylinder? toyota does have oversized pistons, so if you want to repair the one cylinder you can. but for best results, do all 4.


I'm not sure how bad it is its just some scuffing.

Scraps
Sorry i dont know who makes 7A forged pistons. I have have some made from Diamond. i have a good relationship with them. i use them when i build high HP 2ZZ-GE engines.

if you just ahve some scuffing, then just get it re-honed. you should be just fine. then defiantly just get the oversized piston from toyota and ring set. not worth doing all 4

2001 Celica GT-S Turbo1997 Supra TT 6speed1997 Celica 3MZ/1MZ swap1990 Celica All-Trac
>
QUOTE (Smaay @ Aug 5, 2010 - 4:39 PM) *
>Sorry i dont know who makes 7A forged pistons. I have have some made from Diamond. i have a good relationship with them. i use them when i build high HP 2ZZ-GE engines.

if you just ahve some scuffing, then just get it re-honed. you should be just fine. then defiantly just get the oversized piston from toyota and ring set. not worth doing all 4


I tried honing it... Not so much luck... I'll post pics...

Scraps



Do you think if I try to run the hone through some more it'll come out?

Scraps
drag your fingernail along the scratches, it really doesnt look that bad. a good hone job might clean all that up. if your fingernail catches the scratch it might be too deep for a hone and you need to bore it.

2001 Celica GT-S Turbo1997 Supra TT 6speed1997 Celica 3MZ/1MZ swap1990 Celica All-Trac
>
QUOTE (Smaay @ Aug 6, 2010 - 11:57 PM) *
>drag your fingernail along the scratches, it really doesnt look that bad. a good hone job might clean all that up. if your fingernail catches the scratch it might be too deep for a hone and you need to bore it.

Thanks for being so helpful dude!

Scraps
importperformanceparts.net can get u a set of pistons for the 7afe ... forged with any compression and size up to 82.5mm . stock is 81.0 mm. check them out on price as i dont know how much it would cost but i have the HP engine kit with forged pistons and all... which cost me just over 1000.00 .. on there website if u look they offer just a rod and piston combo, if u all ready have everything else to rebuild it may be a good choice if u want stronger internals ..

This post has been edited by 95celicastLSR: Aug 10, 2010 - 2:09 PM
1000 for forged pistons for a 7a.

Swap!

Learned a lot in 10 years...I hardly log in anymore, last loginToday Sept 6 2019, and I was forced just to clarify a post. LOLIf you PM me and I dont respond, dont fret or cry. Im alive, better post your questions in the thread below, maybe I log back in2grfe Swapped...Why I chose the 2GR, before you ask read here...A great civilization is not conquered from without until it has destroyed itself from within.@llamaraxing in Instagram is the best way to find me. I hardly log here anymore.
>
QUOTE (njccmd2002 @ Aug 10, 2010 - 3:11 PM) *
>1000 for forged pistons for a 7a.

Swap!

x2
>
QUOTE (Johnnyny @ Aug 11, 2010 - 12:50 AM) *
>>
QUOTE (njccmd2002 @ Aug 10, 2010 - 3:11 PM) *
>1000 for forged pistons for a 7a.

Swap!

x2

it cost me 1000 for the whole HP engine rebuild kit.... lol got to be nuts to pay 1000 for just pistons !!!
I honed it some more and it finally smoothed out... I just have to finish my head now and I'm done.

Scraps