The_enD

#1

Hello my name is Teo and this is my Celica. My focus is on audio and interior/exterior changes. Hope you enjoy.
7a-fe running on LPG, the rims are 16" OZ Superleggeras





I found a suitable hole to run the 0ga through the passengers side firewall. But my battery is on the drivers side. As I knew I will be upgrading my stock wire I decided to avoid running such a thick wire across the engine bay and connect it straight to the alternator. One little thing- the alternator positive bolt was a little bit short for the ring terminals at the same time. Went and bought this "tube" that is threaded on the inside.
Terminal for 0ga, washer, "tube" thingy, 5ga going from alternator + to battery +


Back seats be gone!


Falls floor done with multiple pieces to save on material. Practically zero spend on it.


Carpet


The box - 1.75 cub feet, kerfed port @ 32, 1.5 inch plywood walls
















Port painted in white satin


1.75 walls






Bad ass terminals






Sub - Sundown Audio SA-12 , Amp SAZ-1500D




This post has been edited by The_enD: Jun 26, 2014 - 4:18 AM

---

FS thread :Custom Celica partsmade to order + moreClick the image to visit my FB page

The_enD

#2

Each door will have a single 10" Neopro in a ported plywood enclosure tuned to around 60Hz. Adding fiberglass for even more strength.

Plywood

Door inner cover and front baffle for the enclosure.




Flushed driver




Big hole for the enclosure. Door will be covered in suede.


Port


Assembly






The flush weakened the baffle, so I added two pieces at the back of it for strength.


After the glue dries I will cut it out again.


Attention to details. Even tho it won't make a significant difference the piece was rounded over.
This piece is kinda of a brake point for the to separate, so called sections of the enclosure.


And the round over is here


8 clamps and left to dry.










Cut them up to save some space in the front by doing some relocations.


Glued back on


Fiberglassed the original panel to the ported enclosures




Covered some parts of the wood and fiberglass with foam for a softer feel when I cover them up.


Rice


Old and ugly gear ball


New

---

FS thread :Custom Celica partsmade to order + moreClick the image to visit my FB page

The_enD

#3

I bought the car with the original steering replaced with a MOMO RACE and decided to keep it. The leather was in bad shape tho so:

Test piece


Before






What happens when your hands are slightly wet -_-



Making holes, no thread in the needle


First piece done


Making a pattern for the more complex shapes


Connection stitch with black thread. It will be will be touched more, and if it was white, after a while it was bound to get dirty.






The finished product of my imagination












Overall I am very please with the result. It took me around >>20-24>> hours of hand work, measuring, cutting, using the sewing machine, making patterns, failures, stitching.

Used : white and black polyester thread, real leather from some dead animal, scissors, shaving blade, 3 needles, glue.
*optional : patience, good taste, the internet

---

FS thread :Custom Celica partsmade to order + moreClick the image to visit my FB page

Malek

#4

Wow! Great job on that steering wheel!

I seriously need to do that..*have* some one do that to for me haha

---

SPYRO|DARKSPYRO|CYRIL

SwissFerdi

#5

Excellent job on that steering wheel, must be rewarding to handle your own craftsmanship daily.

---

'97 ST\ Eibach \ KYB \ Kenwood \ Alpine \ Cusco \ OEM+[sold 10/18]'93 MX-5LE

smkr3w

#6

Very nice, on everything!
Liking the sound setup as well.
I thought I had patience with projects but all that detail..

---

6gcHeroes:808hectortimmybatmandiegotigamak

Legen-dary

#7

Wow! Yeah that steering wheel looks professional, nice job! Looks like you have a nice setup for woodworking too!

---

1999 Celica GT Auto - GF's car1996 4Runner SR5 5sp - Ol' Faithful2006 Evo 9 MR - For sale1998 Supra NA Auto very slow

Syaoran

#8

I love seeing different things like this. Keep up the good work!

---

1993 Celica GT Coupe - sold1994 Celica GT Liftback

The_enD

#9

Thanks, all

I am currently doing 141.7dB at 35Hz. But there is a competition in a month and I am hoping for a slightly higher result.
And I have an 18 inch subwoofer shipping later this year.

---

FS thread :Custom Celica partsmade to order + moreClick the image to visit my FB page

Lil-Joe101

#10

Awesome build dude

---

FromJapantoTexasmy st202 follows me.Being different from every angle of the word, leading the Revolution (TOYOTA NATION)The RHD st202 that made it from Japan check it out.http://www.6gc.net/forums/index.php?showtopic=78103

Malek

#11

>

QUOTE (The_enD @ Apr 13, 2013 - 1:56 AM)

>Thanks, all

I am currently doing 141.7dB at 35Hz. But there is a competition in a month and I am hoping for a slightly higher result.
And I have an 18 inch subwoofer shipping later this year.

Are you using the small space of the Celica to your advantage?? I'm not too into sub competitions or anything but I've briefly read about people ordering subs to match the dimensions of their car. Volumetrically, their car is the sealed box.

Idk..maybe I'm making all of that up haha I thought it was a cool idea but yeah, keep up the good work

---

SPYRO|DARKSPYRO|CYRIL

The_enD

#12

>

QUOTE (Lil-Joe101 @ Apr 13, 2013 - 10:41 AM)

>Awesome build dude

Thanks.

>

QUOTE (Malek @ Apr 13, 2013 - 8:42 PM)

>>

QUOTE (The_enD @ Apr 13, 2013 - 1:56 AM)

>Thanks, all

I am currently doing 141.7dB at 35Hz. But there is a competition in a month and I am hoping for a slightly higher result.
And I have an 18 inch subwoofer shipping later this year.

Are you using the small space of the Celica to your advantage?? I'm not too into sub competitions or anything but I've briefly read about people ordering subs to match the dimensions of their car. Volumetrically, their car is the sealed box.

Idk..maybe I'm making all of that up haha I thought it was a cool idea but yeah, keep up the good work

Nah, I am not that fancy, it's just my daily with a loud system in it.
But a hatch works good for my purpose.
When the 18 comes tho I have a plan on walling it - basically you put a wall behind(one of the six of the box) you and mount the driver and port on it. Will be nuts.

---

FS thread :Custom Celica partsmade to order + moreClick the image to visit my FB page

The_enD

#13

It's the small things.

Headliner bulbs changed to LED SMD's






I had a 1 meter/60 LED's strip which I cut from. Soldered and used the 3M tape on the back to attach to the inside. It was a bit time consuming, but I decided to not waste my time looking for bulbs and save some money. Under $1 upgrade.

This was shot in complete darkness with no flash, the LEDs are the only light source.


Next thing I did was use the same LED strip and do my license plate light.









And even more lights. This is a Ultraviolet neon. You can hardy see it at day and night, but add some white to it and the effect is there. Cool with white shoes or laces.

---

FS thread :Custom Celica partsmade to order + moreClick the image to visit my FB page

The_enD

#14

Teaser on what I've been working on.

---

FS thread :Custom Celica partsmade to order + moreClick the image to visit my FB page

JoshuaM

#15

Interesting concept with the chairs... I haven't seen it don't like that before; can't wait to see how it turns out

I love your work on the steering wheel too; looks plush

---

SOLD :( 1997 ST204 Celica ZR ----->See it here on 6GC!2013 October Celica of the Month XDNow: '00 NB8B Mazda MX5 ----->See it here in off topic!

SwissFerdi

#16

That's a great idea, Aston Martin did it, I believe.

This post has been edited by SwissFerdi: May 6, 2013 - 6:34 AM

---

'97 ST\ Eibach \ KYB \ Kenwood \ Alpine \ Cusco \ OEM+[sold 10/18]'93 MX-5LE

The_enD

#17

Thanks guys.
I've got quite a few interior ideas from Lamborghini.

---

FS thread :Custom Celica partsmade to order + moreClick the image to visit my FB page

The_enD

#18

Couldn't resist posting my unfinished project



How would you guys like a white Toyota emblem on that headrest?

---

FS thread :Custom Celica partsmade to order + moreClick the image to visit my FB page

TRock303

#19

Some seriously nice work on the wheel man, impressive door setup as well. Patience is a virtue!

The_enD

#20

>

QUOTE

>Patience is a virtue!

Hey, that's my moto!
Thanks, man.

One seat is mounted, minor things I have to touch up, but apart from that it's ready.
Pics soon.

---

FS thread :Custom Celica partsmade to order + moreClick the image to visit my FB page

cheela

#21

love the steering wheel and the seats are looking so unique and cool.
I'm not much for sound and don't know much but what you're doing is right on the money too.

---

*1997 Celica ST - 3SGE Greytop BEAMS*1977 Celica RA29 - Classic Cruiser*2005 Matrix AWD - dedded but still hanging around like a ghost2019 Rav4 XLE Premium - Sports mode is fun.

The_enD

#22

Thanks, cheela.

Promised pictures




Drag style , no back seat and seat belts, no passenger seat, no cards on both doors, no spare.


Stock vs Custom

---

FS thread :Custom Celica partsmade to order + moreClick the image to visit my FB page

Legen-dary

#23

Really love the pattern and material that you did for the seat cover, it looks great! Personally I would have kept the separated headrest but that's really just a matter of opinion. Is there a reason that the material looks "looser" than the factory seat? Did you reuse the metal bars from the factory cover and stitch them into the underside of your covers and staple them back to the foam?

---

1999 Celica GT Auto - GF's car1996 4Runner SR5 5sp - Ol' Faithful2006 Evo 9 MR - For sale1998 Supra NA Auto very slow

The_enD

#24

>

QUOTE (Legen-dary @ May 9, 2013 - 4:41 PM)

>Really love the pattern and material that you did for the seat cover, it looks great! Personally I would have kept the separated headrest but that's really just a matter of opinion. Is there a reason that the material looks "looser" than the factory seat? Did you reuse the metal bars from the factory cover and stitch them into the underside of your covers and staple them back to the foam?

Thanks.
Yes indeed it is loose in some places. I used the original metal straps, but my cover was just not perfect replica of the old one and add to that a new headrest there were some imperfections. I may end up redoing in the future. I'll make sure I take more time with the driver's seat, but in the end it's my first time doing anything like this and I lack experience as a tailor.

---

FS thread :Custom Celica partsmade to order + moreClick the image to visit my FB page

Legen-dary

#25

>

QUOTE (The_enD @ May 9, 2013 - 7:11 AM)

>>

QUOTE (Legen-dary @ May 9, 2013 - 4:41 PM)

>Really love the pattern and material that you did for the seat cover, it looks great! Personally I would have kept the separated headrest but that's really just a matter of opinion. Is there a reason that the material looks "looser" than the factory seat? Did you reuse the metal bars from the factory cover and stitch them into the underside of your covers and staple them back to the foam?

Thanks.
Yes indeed it is loose in some places. I used the original metal straps, but my cover was just not perfect replica of the old one and add to that a new headrest there were some imperfections. I may end up redoing in the future. I'll make sure I take more time with the driver's seat, but in the end it's my first time doing anything like this and I lack experience as a tailor.

Certainly you're very talented and for just taking on these tasks you're doing a fantastic job. I'm sure you're learning more as you go along and it will just keep getting better and better!

This post has been edited by Legen-dary: May 9, 2013 - 10:12 AM

---

1999 Celica GT Auto - GF's car1996 4Runner SR5 5sp - Ol' Faithful2006 Evo 9 MR - For sale1998 Supra NA Auto very slow

The_enD

#26

Аppreciate the words. I certainly am learning some stuff and want to make it into a profession one day. What a better way than my own car.

---

FS thread :Custom Celica partsmade to order + moreClick the image to visit my FB page

The_enD

#27

Finally :















Some minor things to be touched up, but this gives you an idea how it will look. The material is the same as the seats, kinda feels like suede.
Port will be painted black, a grill will be made. One more door to go...5 days to competition!

---

FS thread :Custom Celica partsmade to order + moreClick the image to visit my FB page

travisxcore

#28

I think this is some of the best interior craftsman ship I've ever seen, that is crazy cool dude. Keep up the good work and good luck!

rentaspace

#29

I wish I was half as talented as you are with craftsmanship... Your work makes my craftsmanship look like a 2 year olds HAHAHAA
Amazing job dude Keep it up

---

------------------------------| White '94 Celica | Bought 11/05/12 | Sold 12/05/15 |------------------------------------------------------------| White '02 N-Edition Caldina | Weekend Car |------------------------------

The_enD

#30

Thanks, fellas.

---

FS thread :Custom Celica partsmade to order + moreClick the image to visit my FB page