Rusty

#1

Well since getting the Tom's ECU, I've had a look around where the ecu sits & on toyodiy.


Sits within 2 brackets & has an external relay on one side. So the easiest way would be to bring the whole thing out in one go. Did you have to remove any interior trim pieces or can you get away with not removing any?



Also remember its an ST202 so RHD, passengers side = L

---

ST202 SS-II CELICA threadNew Zealand members check inSticky thread's: How to contribute and troubleshoot.

Neon90424

#2

I believe mine ws behind the radio on my gtfour

---

What I think when you think I care

Rusty

#3

yes I know where it is, I'm trying to remove it to put this in

---

ST202 SS-II CELICA threadNew Zealand members check inSticky thread's: How to contribute and troubleshoot.

malpaso

#4

>

QUOTE (Rusty @ Oct 23, 2013 - 9:32 AM)

>

this is really pure sex...

---

No more replicas... This is evolution... This isSS-four:)________[Featured Celica of 6gc.net @ 2010]_________

richee3

#5

I was able to remove mine by pulling the carpet down on both sides of the console, then a little wiggle work to maneuver it out.

---

"Employ your time in improving yourself by other men's writings, so that you shall gain easily what others labored hard for." -Socrates. Even Socrates told us touse the search button!2006 Aston Martin V8 Vantage.1998 Celica GT-BEAMSSwapped.2022 4Runner TRD Off Road Prenium.2021 GMC Sierra AT4.

stalker76

#6

>

QUOTE (Rusty @ Oct 23, 2013 - 3:32 AM)

>yes I know where it is, I'm trying to remove it to put this in

Hi Rusty, Hi Malpaso!!

Great!!!

But where i can find one for my 3SGE Beams?
if you have a link......

Rusty

#7

thanks richee


stalker76, you will never find one as they didn't make one for the redtop beams

---

ST202 SS-II CELICA threadNew Zealand members check inSticky thread's: How to contribute and troubleshoot.

FORGMANN

#8

Curious to see what TOMS ecu does . Sure my Imec tuned 3sge ecu similar
Sadly i will never know as not using ecu or motor in anything ever.
Can't wait for dyno results .



This post has been edited by FORGMANN: Oct 23, 2013 - 7:47 PM

---

Old guy with the toys95 ST205 WRC (the real deal)94 MR2 HARDTOP Supercharged 2GR/6SPD 22 owned

Rusty

#9

I emailed the I-Mec/I-Code group awhile ago when you posted yours to learn more about it. I'm sure the reflashed/ plug in ecu's Tom's TECS II, I-Mec, C-One Power ECU, Biltz Access etc do the same stuff replaced daughterboard to allow changes to be made, and is optimised to the owner and mods they have.

>

QUOTE

>セリカＳＴ２０２用　アイメック製ＥＣＵは、点火、　燃料調整、スピードリミッターカット　３種類が変更してあります。

Thank you for your e-mail.

We announce you the contents of the IMEC (change & contents are the same as icode in the name of four years before & company)ECU for Celica ST202.

1) Ignition timing adjustment
2) Fuel increase in quantity.
3) speed limiter cut of 180km.

...

not sure if the speed cut is completely removed or just moved up higher like the HKS SLD

---

ST202 SS-II CELICA threadNew Zealand members check inSticky thread's: How to contribute and troubleshoot.

stalker76

#10

>

QUOTE (Rusty @ Oct 23, 2013 - 4:14 PM)

>thanks richee


stalker76, you will never find one as they didn't make one for the redtop beams

Rusty, what sort of ECU i must to buy for my 3SGE redtop Beams?

Rusty

#11

1. has the ability to run your engine - vvti
2. Your tuner who knows & is familiar the ecu that will do the maps etc


I've heard of people using the Apexi Power FC from the 1ZZ-FE for the beams, as they're both similar to each other.

Chances are you'll get a standalone ecu, which will cost a bit, plus wiring/install and then on top of that more dyno/tuner time to set up all the vvti changes

---

ST202 SS-II CELICA threadNew Zealand members check inSticky thread's: How to contribute and troubleshoot.

stalker76

#12

Thanks for the advice Rusty!

Obviously I know that everything would cost ... but the money is not a problem ... the only problem is that here in Italy .... not familiar with the celica ... figured engines Beams: D

For this I registered on 6GC, surely you are much more than any enced mechanic here in the area.

I've heard that on Beams use the Apexi Power FC

mgnt232

#13

i couldnt get mine out for the life of me from the side lol. I did it a long time ago, but remember I had to pull out the whole "shifter console". but i mean thats like 4 screws, easy in and out either way

---

I've spilt my heart into this car :) And I don't ever plan to stop- 6GC for Life ->Semper Fi<1994 Cupra :p 3sgte1995 Celica ST DD1969 Chevelle SSalllll balls. P2 approved!

onnaj

#14

For my 7AFE ECU it was really easy. Pull the carpet down. Unscrew the 3 bolt, wiggle a bit and pull it out. Ow yeah, first unplug the connectors

But normally it's a really easy (10 min) task.

This post has been edited by onnaj: Oct 26, 2013 - 9:29 AM

---

My 7AFE to 4AGE 20V Blacktop conversion!