Over 1M Posts • 84K Topics • 9K Authors

Home > Topic #93981

bolt sizes? - 6G Celicas Forums

Topic #93981 8 posts Started by Arturio55
Arturio55
#1
Is there any website or manual I can download that will tell me the sizes of all the various bolts on a 3sgte and the 6gc engine bay? Been acquiring tons of parts for my swap and sadly some of them were shipped without bolts, including the tranny (shame on all of you selfish sellers...jk jk)
if not is there anyone with a vast knowledge of our engine bays who can relay the info to me
QUOTE (Azncelica @ Mar 4, 2012 - 11:43 PM)I started with what I know to do, I swap engine into my car, I knew it was too much work to make it a AWD. I kept it FWD. Went to take a crack at doing the wiring conversion. Than, I realize, shoot, this is out of my league.
Smaay
#2
most everything is a 10, 12, or 14 bolt head. there are a few 17mm bolt that bolt the trans to the block.

10mm are a M6X1
12 are M8X1 (I think)
14 are M10X1.25
bolt lengths will vary for everything, what I typically do looking for a bolt is stick a bolt in the hole. if it goes in about 3/4 of the distance then it should be a good candidate. if It goes in and it almost bottoms out its not long enough
2001 Celica GT-S Turbo1997 Supra TT 6speed1997 Celica 3MZ/1MZ swap1990 Celica All-Trac
njccmd2002
#3
Go to a yard . Get bolts from there. Check ebay for bags of bolts. New bolts can get pricy...
Learned a lot in 10 years...I hardly log in anymore, last loginToday Sept 6 2019, and I was forced just to clarify a post. LOLIf you PM me and I dont respond, dont fret or cry. Im alive, better post your questions in the thread below, maybe I log back in2grfe Swapped...Why I chose the 2GR, before you ask read here...A great civilization is not conquered from without until it has destroyed itself from within.@llamaraxing in Instagram is the best way to find me. I hardly log here anymore.
Arturio55
#4
>
QUOTE (Smaay @ Oct 28, 2014 - 2:49 PM) *
>if it goes in about 3/4 of the distance then it should be a good candidate.


thats what she said lolol



>
QUOTE (njccmd2002 @ Oct 28, 2014 - 3:44 PM) *
>Go to a yard . Get bolts from there. Check ebay for bags of bolts. New bolts can get pricy...


thanks ill check ebay. sadly 6gc's are in rare form in new jersey, doubt ill find one at a local junk yard
if i get the 205 tranny will all of those bolts fit on an s54?
ill try to utilize what i can from my 7afe but i feel like that'll be a long shot.

and smaay thanks i didnt realize they only used those few sizes, although i have spent quite some time in my engine bay over the past 2 years...

This post has been edited by Arturio55: Oct 28, 2014 - 2:54 PM
QUOTE (Azncelica @ Mar 4, 2012 - 11:43 PM)I started with what I know to do, I swap engine into my car, I knew it was too much work to make it a AWD. I kept it FWD. Went to take a crack at doing the wiring conversion. Than, I realize, shoot, this is out of my league.
njccmd2002
#5
any toyota bolt will do, does not have to be from a celica
Learned a lot in 10 years...I hardly log in anymore, last loginToday Sept 6 2019, and I was forced just to clarify a post. LOLIf you PM me and I dont respond, dont fret or cry. Im alive, better post your questions in the thread below, maybe I log back in2grfe Swapped...Why I chose the 2GR, before you ask read here...A great civilization is not conquered from without until it has destroyed itself from within.@llamaraxing in Instagram is the best way to find me. I hardly log here anymore.
Arturio55
#6
>
QUOTE (njccmd2002 @ Oct 28, 2014 - 7:17 PM) *
>any toyota bolt will do, does not have to be from a celica

Wasnt sure if theyre all the same length
also I got the resistor pack yesterday, thanks
QUOTE (Azncelica @ Mar 4, 2012 - 11:43 PM)I started with what I know to do, I swap engine into my car, I knew it was too much work to make it a AWD. I kept it FWD. Went to take a crack at doing the wiring conversion. Than, I realize, shoot, this is out of my league.
schmooot
#7
m6 x 1
m8 x 1.25
m10 x 1.25
m12 x 1.25

I can confidently say that from my experience 98% of any Toyota ever will use those 4 thread sizes. I've got 4 huge bins dedicated to those and I just keep filling them up every time I wreck a toyota or honda
ST205 Crew representChallenge Accepted
Arturio55
#8
>
QUOTE (schmooot @ Nov 26, 2014 - 12:22 AM) *
>m6 x 1
m8 x 1.25
m10 x 1.25
m12 x 1.25

I can confidently say that from my experience 98% of any Toyota ever will use those 4 thread sizes. I've got 4 huge bins dedicated to those and I just keep filling them up every time I wreck a toyota or honda


What about the various 14 and 17mm bolts in the engine bay?
Need bolts for all the engine/trans mounts and brackets
also you should send me some free bolts smile.gif I'll pay shipping
QUOTE (Azncelica @ Mar 4, 2012 - 11:43 PM)I started with what I know to do, I swap engine into my car, I knew it was too much work to make it a AWD. I kept it FWD. Went to take a crack at doing the wiring conversion. Than, I realize, shoot, this is out of my league.
← Back to Topics