Suspension/Handling/Braking
5,114
Total Topics
25
Showing
12
Page 12 of 205
Topics in Suspension/Handling/Braking •
newest topics first
I am very happy with the teins but I want to be tucked since I look like a 4x4...
Hello guys as I said on the title, my power steering pump is leaking, I m thinking to replace the seals with this,
http://www.ebay.co.uk/itm/Power-Ste...
No pointers? Don't want to spend a grand on something that
might
not work...
depends how low you want. You can fit up to 215/45/17. Maybe even stuff 225/45/17 in it also. So 205 for hella stretch, 215 for stretch, 225 for sligh...
If I recall, I have Mevotech on the front and Moog on the rear. I just remember that they were thicker than the OEM version. Just look at the link pro...
Hey,
last night i had to get towed home due to only having 1 stud still intact last night, seems that they broke off sometime yesterday. Is there a li...
Chassis wise you may be ok. But the st engine may not fit on the gt crossmember, still need the st crossmember...
I have an old (perhaps over 50 years old) Federal B-21 dial indicator (0.0001") that I had been using to measure run-out. Lately, it seems sticky and ...
Does anyone happen to know the thread/length/type of the OEM lug nuts?
I would say for the ST204, but feel free to post up other models as well. I wou...
ADDED NOTE:
I am not a trained auto mechanic; I try to DIY whatever I can to keep my 300,000 mile Celica happily running. Thanks to a wise comment bel...
Could just be a matter of tightening the cable. First thing to check anyhow.
Also you should be putting it into reverse if the nose is sloping downwa...
Bought new cv axle from o Riley. Not remanufactured. Had a guy put it in for 50 in a local garage. On the way home I noticed the car vibrates on st...
^yup.
pair the KYB GR2s with Eibachs, TRDs, or TEINs. They all give relatively the same drop....
6gcs definately look better an inch or two lower.
Some wheels and sideskirts would definately make it look sexier too....
Alignment probably needs to be redone because of the cambe adjustment you made. I adjusted mine to have more camber jn the front and it caused my stee...
All of the above is good advice. That said, I'd check the anti-sway bar bushings, because it's an easy thing to test and a cheap fix.
Simply disconnec...
I'm looking at lowering my convertible but wanted to use the TRD springs (trying to keep everything stock/toyota, I know the TRD springs aren't made b...
A workshop swapped the motor and entire drivetrain from a jdm gt4 to my gt4. When they did the job the 19" was on it. When i got it back i almost immi...
Car = convertible 6g w/ 3rd gen 3sgte and tons of engine mods
Feel free to only answer one if you don't know the questions to all...
questions:
1) I'v...
Langing here:
Found a document on-line that identifies the rear axle nut torque spec I needed; it is 90 foot pounds. Someone else might appreciate the...
250 i paid for mine back in da day...
I got an AT200 too. just bought a set of MEGAN EZ streets and gonna be installing them soon....
Hows it going, this is more directed at 5g's but what is built for those spills over to 6th and 4th gens too so I found this would be important to y'a...
i have always had a thing for steelies and was looking into steel banded steelies.
for those who dont know what banded steel wheels are... its basical...
195/45/16 Toyo Proxies. Not a normal shop. It's s used tire place and I know the owner. He gets a thrill out of stretching tires...