Soulend

#91

>

QUOTE (HectortheRican @ Nov 12, 2010 - 12:42 PM)

>That swap needs to be Rick rolled by you. You will never give that swap up. You'll never let it down. You'll never run around and desert it.

*Thumbs up!* made me lol.

so another update,

installed the new/old TVSV Manny sent me! Thanks a lot! . umm finally got the steering pump figured out, however, Stevenson, if you could still take those pictures they maybe of use for me! most of the vac lines are hooked up. just steering and the IAC I believe. I think i might do something similar to what manny did and just put a small filter in for that.

here is a video:
http://www.youtube.com/watch?v=NmpNqAcbUw0

purplegt4

#92

get a helper to twist the bolt while you're holding it in place.

Soulend

#93

>

QUOTE (purplegt4 @ Nov 12, 2010 - 6:30 PM)

>get a helper to twist the bolt while you're holding it in place.

my problem is, I'm not sure how to get it really tight haha

Soulend

#94

wooot! she purrs beautifully now! Ill take a video after I go bowling with the Japanese Association (I'm a club officer) then Ill try and tighten up the steering and get filters mounted up and the inter-cooler figured out then the beast is done! well on my end anyway haha

Kevin

HectortheRican

#95

AWESOME!

Can't wait

---

taking too long to mod since '09June '12 COTM'95 AT200

Soulend

#96

As promised a video for your enjoyment!

http://www.youtube.com/watch?v=hF5ps3pmb4o

Kevin

njccmd2002

#97

nice finally

---

Learned a lot in 10 years...I hardly log in anymore, last loginToday Sept 6 2019, and I was forced just to clarify a post. LOLIf you PM me and I dont respond, dont fret or cry. Im alive, better post your questions in the thread below, maybe I log back in2grfe Swapped...Why I chose the 2GR, before you ask read here...A great civilization is not conquered from without until it has destroyed itself from within.@llamaraxing in Instagram is the best way to find me. I hardly log here anymore.

HectortheRican

#98

It sounds so damn THROATY

---

taking too long to mod since '09June '12 COTM'95 AT200

Soulend

#99

>

QUOTE (HectortheRican @ Nov 13, 2010 - 8:55 PM)

>It sounds so damn THROATY

that sir... is a 3" down pipe at work lol

HectortheRican

#100

Is it just the downpipe or have you connected the exhaust?

---

taking too long to mod since '09June '12 COTM'95 AT200

Soulend

#101

>

QUOTE (HectortheRican @ Nov 13, 2010 - 9:13 PM)

>Is it just the downpipe or have you connected the exhaust?

just a down pipe atm. when the engine is finished there is a local shop who will run 3" exhaust for $250 real nice guys.

Kevin

HectortheRican

#102

Good stuff!! I was gonna say.. that sounds a bit too throaty to have a muffler attached

---

taking too long to mod since '09June '12 COTM'95 AT200

Soulend

#103

haha, Just a tad man. but it is still fun haha. I'm going to drive around my neighborhood a couple times to piss people off... I have SOOO many people who drive up and down the street really fast, loudly or some fashion of annoyance... so I'm going to have my little bit of fun.

Kevin

presure2

#104

awesome kev!
i assume the tranny bracket i sent fit?

---

Former Team 5SFTE pro member ;)13.6@108MPH, 5SFTE Powered

Soulend

#105

>

QUOTE (presure2 @ Nov 14, 2010 - 5:56 AM)

>awesome kev!
i assume the tranny bracket i sent fit?

yeah! crazy enough to the 6gc mount! Thanks a lot. I'm going to try and get most of it buttoned up today . amd hopefully going up and down the street by the end of the week.

Kevin

presure2

#106

>

QUOTE (Soulend @ Nov 14, 2010 - 10:41 AM)

>>

QUOTE (presure2 @ Nov 14, 2010 - 5:56 AM)

>awesome kev!
i assume the tranny bracket i sent fit?

yeah! crazy enough to the 6gc mount! Thanks a lot. I'm going to try and get most of it buttoned up today . amd hopefully going up and down the street by the end of the week.

Kevin

awesome.

---

Former Team 5SFTE pro member ;)13.6@108MPH, 5SFTE Powered

purplegt4

#107

great job!

Soulend

#108

this ST has black hard lines running up the pass side for the steering lines, can I just delete those and run hose from the hard line under the engine?

Soul

presure2

#109

>

QUOTE (Soulend @ Nov 14, 2010 - 5:49 PM)

>this ST has black hard lines running up the pass side for the steering lines, can I just delete those and run hose from the hard line under the engine?

Soul

those are steering "cooler" lines.

you "can" remove them, not a huge deal, but i would leave them if you can.

---

Former Team 5SFTE pro member ;)13.6@108MPH, 5SFTE Powered

Soulend

#110

okay good to know thanks. Ill keep them on. on the plus side... means i need less hose

Kevin

Soulend

#111

I'm Stuck at a point... I can't find correct hose for the intercooler lines. 7/8th is a hard type to find I guess... Also, I have no wiring experience and i have to wire in a rely for the water pump...

The more I read on what to do, the more I become confused heh

Kevin

Soulend

#112

ugh so I got the car down off of the jacks, started it up and car goes nowhere because of the transmission and clutch... I get 2 inches of play after bleeding it. and its not moving the the clutch to engage. then while checking the gears a little black plastic piece came off the peg on the 'up down' shifting bar...

Curse of the evil Canadian transmission....

if you have help tips please let me know...

Kevin

presure2

#113

kev, head down to your local pepboys or whatever, (harbor frieght if you have one near you) and buy a mighty vac.
before you start the bleeding process, pull the bleeder screw completely out, and thread tape the threads.
install the bleeder, tighten it enough so it dont leak.
*put the mighty vac on it, and pull ~ 25 vac on it. have your dad or someone press the clutch pedal 8-10 times quicky, and hold down the pedal on the last pump.
then loosen the bleeder while you continue to pump up the mighty vac, and have someone keep an eye on the fluid level.
close the bleeder before the resivour for the mighty vac is full, empty it, and repeat the bleeding process from the asterik down.
you should be able to watch the slave cylinder open and close as someone pushes the pedal after that.
i can usually get it working properly with only one cycle, but you may want to do it X2 like i said, just to be sure.
take a pic of what came off.

---

Former Team 5SFTE pro member ;)13.6@108MPH, 5SFTE Powered

Soulend

#114

thanks manny, it still feels like 2" of play... maybe that's what it is meant to be.

but the real problem is, the car just wont go into gear... I can have my friend confirm that it was put on the engine before the trans was put on.

when I put it into reverse it sometimes grinds (probable from me moving it too fast) so I KNOW its going into the gear... so the power isn't getting to the axles I'm assuming...

any other pointers?

Kevin

maybe I have to adjust the cables or something like that? I mean like I said it IS going into reverse... so I don't think that could be it...



This post has been edited by Soulend: Nov 19, 2010 - 12:10 AM

Culpable04

#115

you need to fix the free play issue first, trans will not go into gear while the clutch in is contact with the flywheel, I had this same problem but my system was bleed properly so all I had to do was adjust the height of the pedal and I was able to drive the car perfectly.

make sure you bleed your system properly, and then adjust the pedal height and release point of the clutch, then you'll be able to shift properly.

Soulend

#116

okay... I think I Figured it out... it doesn't make sense to me but... I think the axles are wrong and that is causing the problems... so it comes down to the fact that I was told when i got it, that it was a 92 5SFE out of a Camry... so I ordered 92 celica GT axles... well I've been finding out that its most likely out of a 94 camry, still a 5sfe. I dont know how this all works out but I hope to god that a longer axle will get in properly and get power to the wheels...

today, I jacked the car up again turned it on, put the car in gear and tried spinning the wheels, they spun freely. I noticed the axle jumping around a bit near the trans. so i felt and I could feel something like a gear spinning around it. well when my dad got home he mess around with it, and the gears wouldnt go in unless I pressed the clutch in and the wheels wanted to turn... but still not well enough.

so I hope i can get the driver side tomorrow and see if it changes anything,

Wish me Luck,
Kevin

Culpable04

#117

if you are using a 1992 celica axle, it's not long enough for a 6th gen

presure2

#118

you need to get a set of 94-99 celica gt axles, dude.

---

Former Team 5SFTE pro member ;)13.6@108MPH, 5SFTE Powered

Soulend

#119

yeah, I totally wasn't thinking distance between wheel and trans, but a change on where they connected... easy fix compered though...

Kevin

Soulend

#120

well come to find out, I had to pound the axle in... so i ordered the right one...

anyway got everything set up to test drive over the weekend... I put the car in reverse... and it moves!!! I get it into the street, put it in first... and it goes nowhere... the effin pass side axle popped out this time... I was stumped... well come to find out, I needed a bracket for the carrier bearing... which didnt come with the engine and nor was it on the ST... and guess what... that pressed on back part of the bracket? its expansive or hard to find... awesome... another week down the tubes...

Kevin