deathdoakill

#1

weeeelllll these are just some pics of an idea i had an remember we are thinking outside the box here not the traditional look. so im gonna try to finish this before my next surgery a little before the 14th feed back always welcome here as well as ideas
very rough fabrication pics prepping to start fiberglass mold
and some might notice the fender is cut in half already and recessed in a bit i will be fabricating a new version to go with the new hood which will tilt forward

Tigawoods

#2

hmm curious to see the result of this

---

1995 GT::::Diffusing the Situationエキサイティングカーレーシングチーム!march2010 COTM:6GCfeature2014:january2015-2016-2018 COTM

kurt95gt

#3

One peace front end?
Looks like your off to a good start

---

95 gt coupe, v6 swap weekend toy99 gt hatch beams swapped wife's94 st hatch my daily driverhttp://www.6gc.net/forums/index.php?showtopic=82235n

yellowchinaman

#4

OMFG!

jordisonjr

#5

Won't your car just shatter if you ever get into an accident?

---

-Protection mode, For when your amp tries to blow its load.1995 Toyota Celica GTS-Daily Driver1999 Chevy Cavalier-Winter Beater1994 Honda Civic CX Hatchback-DeadMy Celica!

deathdoakill

#6

weeellll lets hope i dont get into an accident lol naahhh right now the car is gonna be down indeffinetly until i swap in the new engine(spun rod bearing ) an yes the it had crossed my mind and im putting some thght into strengthening the finished product i have a cupple rolls of kevlar an about 6 yards of carbon fibr to play with as well but who knows accidents tend to be pretty unforgiving as far as custom cars go or any for that matter.

Syaoran

#7

Not to be an ass or anything but I'm guessing this is now going to be a MR-Celica right? lol

---

1993 Celica GT Coupe - sold1994 Celica GT Liftback

kurt95gt

#8

Nope pretty sure its staying Fwd/awd if he converts it

---

95 gt coupe, v6 swap weekend toy99 gt hatch beams swapped wife's94 st hatch my daily driverhttp://www.6gc.net/forums/index.php?showtopic=82235n

deathdoakill

#9

lol ill answer that one when i get more into it and have pics

deathdoakill

#10

And no not Mr2 celica lol but not something you would NOT normally see in a celica thgh I'll get to that later thigh.

This post has been edited by deathdoakill: Jun 16, 2012 - 10:46 AM

Lil-Joe101

#11

Deff wanna c how this turns out. Pretty epic so far.

---

FromJapantoTexasmy st202 follows me.Being different from every angle of the word, leading the Revolution (TOYOTA NATION)The RHD st202 that made it from Japan check it out.http://www.6gc.net/forums/index.php?showtopic=78103

deathdoakill

#12

surgery got pushed back to the 6th so ill be working on this again this week

deathdoakill

#13

more pics to come people almost able to walk again lol

mgnt232

#14

Cant wait to see the end man, and get better soon

I just bought my supra headlights, and debating between 2 different bumpers. Maybe ill post them up and get some feed back. But i will be able to work on my car in a couple months and create my science project

---

I've spilt my heart into this car :) And I don't ever plan to stop- 6GC for Life ->Semper Fi<1994 Cupra :p 3sgte1995 Celica ST DD1969 Chevelle SSalllll balls. P2 approved!

deathdoakill

#15

Ok walking again still painful but doable. so I started getting ready for fiberglass ing tonight an will have updates in about a week or two as money is a bit of an issue at this point in time since I've been on leave from work .so when money is coming back in I'll be finishing the project an making more progress again.

Will start fiberglass by tomorrow after more prep work.



Ok I'm thinking about cutting the bumper in half where the blue stops and having the bottom section stationary for easier. Removal since all that is taped up will be one complete piece plus makes it easier when separating parts later
Or option two front end and hood an fenders all one complete piece but makes the process a lot harder to do. What do you guys think ?





I am also thinking about changing the side skirts and rerouting the exhaust to come out through the bottom section of the side skirt since the engine swap we are doing is a v 6 but not a major fan of that style



Or should I leave these side skirts on there????

mgnt232

#16

supra skirts

---

I've spilt my heart into this car :) And I don't ever plan to stop- 6GC for Life ->Semper Fi<1994 Cupra :p 3sgte1995 Celica ST DD1969 Chevelle SSalllll balls. P2 approved!

njccmd2002

#17

---

Learned a lot in 10 years...I hardly log in anymore, last loginToday Sept 6 2019, and I was forced just to clarify a post. LOLIf you PM me and I dont respond, dont fret or cry. Im alive, better post your questions in the thread below, maybe I log back in2grfe Swapped...Why I chose the 2GR, before you ask read here...A great civilization is not conquered from without until it has destroyed itself from within.@llamaraxing in Instagram is the best way to find me. I hardly log here anymore.

1000_needles

#18

the purpose of the hole in the fender is to let hot air flow out, not cold air flow in....
looking good

deathdoakill

#19

yezz sir and thanks... not so much negative feedback with the project im pleasantly surprised lol

rave2n

#20

Looks interesting.

My only negative...is doing that to a GT4 hood...could have put some good use to that, and you could have fabbed something unique instead.

deathdoakill

#21

actually yes im planing on doing a different hood an possibly selling ths completed gt4 molded piece later on down the line but not at this point im not sure if im gonna have to change the design because of the engine swap were doing or not thats gonna be a deciding facter here but ive got a really cool design im working on though ill show you guys when im at that point though

mgnt232

#22

cant wait to see a new design idea, especially some new hood ideas. Ive been drawing up some hood ideas of my own, just not 100% yet on any.
And may sound dumb but what happens to the rain water in the top of a gt4 hood? does it just fall on the engine?lol seems kinda dumb
Cause i got some ideas but the water is the only problem im still wondering about

---

I've spilt my heart into this car :) And I don't ever plan to stop- 6GC for Life ->Semper Fi<1994 Cupra :p 3sgte1995 Celica ST DD1969 Chevelle SSalllll balls. P2 approved!

deathdoakill

#23

lol no it has a duct built into it to rout the water out from falliong on the engine an yeah its lotus elise ish hood i was working on lol looks good on paper but we will see ;P

This post has been edited by deathdoakill: Sep 3, 2012 - 10:00 PM

deathdoakill

#24

ohhhhh hey nic i forgot im gonna be making a prototype kit for the celi. ive been working with this new material that is alot cleaner an easier to use... an cheap i think youd be interested in lerning to use

mgnt232

#25

yeah deff just let me know the details about it i reodered my supra front (first order fell through) and may be able to start the project around thanksgiving. even though thats sooooo far away lol.
but send me the details on the new stuff when u got it worked out, thanks again

---

I've spilt my heart into this car :) And I don't ever plan to stop- 6GC for Life ->Semper Fi<1994 Cupra :p 3sgte1995 Celica ST DD1969 Chevelle SSalllll balls. P2 approved!

deathdoakill

#26

Ok it's been a long time I hvent been doing much either you hate it or love it or what ever lol overfender is nearly done got a long way to go still








The front is just an idea I'm playing with pay no attention lol

mgnt232

#27

loving it

---

I've spilt my heart into this car :) And I don't ever plan to stop- 6GC for Life ->Semper Fi<1994 Cupra :p 3sgte1995 Celica ST DD1969 Chevelle SSalllll balls. P2 approved!

Special_Edy

#28

I actually hate bodykits and all things fiberglass, but that is one badass looking car.

You should totally paint it like a stealth jet, And how wide of a wheel will you be able to run?

mkernz22

#29

looks like something out of death race! pretty awesome man!

deathdoakill

#30

Thanks guys much appreciated glad you like the style of over fenders well wheel size is gonna be a considerable difference I've gotta finish my engine swap first thgh which is also a rear wheel drive conversion that's all I'm saying till it's done lol I just decided to finish the body first thgh before anything else.