Forced Induction
3,483
Total Topics
25
Showing
35
Page 35 of 140
Topics in Forced Induction •
newest topics first
i could never get the 5s to run with the ignition side hooked up.
i tried it a few diffrent ways, too.
i would start there....
Ha, you said butt weld.
Congratulations! I'm still very much keeping the possibility of a 7A-FTE open for myself, so I'm quite jealous!
As for a clutc...
A few people have asked me about this and I told them I lost the notes. Well, I found them in my glove compartment after rats had a massive orgy in th...
alright 6gc im trying to plan ahead for my 3s swap but ran into a problem...so like in my other posts my all trac took a turn for the worst so now im ...
forget the hood, to you guys its all aesthetics. it comes from rallying where highly strung 350+ HP engines run at high power for long periods of time...
Gonna turbo my 98 gt and need the part# for a aem fic for my application....
ok so i had alot of codes and cars a/f is way off and while checkign the plugs and harness to make sure the senors were getting ground and power wh...
hi everyone i have recently joined gt4 ownership owned car a few months and ahve a problem with it, my boost gauge a week ago used to read 10 psi on l...
in the 5sfe, is this a possible turbo to put in, I just got it for free. It's from a 300zx....
Best advice is get the harness done by DR Tweak. If your harness is such a mess no matter whether you keep this motor or swap it out for another one y...
QUOTE (dans_st @ Jun 10, 2010 - 12:29 PM)
this may be a simple or NOOB question but I cannot find an answer to.
Can I run an open screamer pipe with a...
JUst bought one for my boosted 7A, just wanting to know if many others have ran this on there turbo'd 7A's? And also what should I know?
I am removing...
3 thousand isnt enough for 1-1700$ engine, then all the belts and fluids..... What else am i missing. Im using my old transmission, already have the h...
get a volt meter and check the map sensor, if that checks out, get a gauge and check fuel pressure....
Don't know the size of the Audi twin scroll, but maybe this is usefull to you:
http://www.modified.com/tech/modp-0906-twi.../full-race.html...
call Aaron at ATS racing www.atsracing.net he said he has a few. he sent me one about a month ago
This post has been edited by
Smaay
: Jun 3, 2010 ...
http://shop.ebay.com/i.html?_nkw=exhaust+w...from=&_ipg=...
A member was looking into fitting a 4afe manifold to the 7a block. According to just about every source available, it looks like it should bolt right ...
a word of advise... i heard the Emanage blue sucks... i have it, but never got the chance to tune. several people say go AEM FIC...
So i got jumped lastnight while i was in my drivers seat and slipped off of my clutch and went into a bunch of **** in reverse and banged up the side...
Ok guys/gals, its been more than a year and i only just got the engine to start a couple weeks ago but it would only idle roughly, then it would just ...
exactly... i have it as wel an only thing I needed to buy is new rad cap. OEM or TRD doesnt fint....
i can only assume you bought a manifold from an ebay seller?
you wont find a quality manifold for the 3rd gen without spending real money on one, or h...
can anyone send me a pic off a ome AT200 fuel pump.
i bourt a used turbo kit on ebay and the guys said its a wellbro pump, i wud put a pic here to sh...
A thing of beauty!...