Engine/Transmission/Maintenance

14,249 Total Topics
25 Showing
58 Page 58 of 570
Topics in Engine/Transmission/Maintenance • newest topics first
11 posts • Started by Box
Air compressor and blow air from the inside out to knock out dirt. I'd imagine the cleaning solution probably isn't much more than de-greaser mixed w...
28 posts • Started by alex_k
A short ram roars while the cold air purrs. I like the roar but some like the purr since it sounds like a whine(aka turbo). Lol....
68 posts • Started by 95CelicaST
6 posts • Started by 95CelicaST
Beams motor has a red valve cover with a red side feed intake manifold, the regular 3sge has a gray intake manifold that runs across the valve cover.....
1 posts • Started by CaliJeff
Hard rattle when press on gas peddle. Won't go faster than 30mph. Clutch pedal feels like a slight rattle to. Rpm dips and rise too. Ideas? Engine reb...
6 posts • Started by 808celica
14x1.5 and 30mm/36mm long i think. make sure to get grade8 bolts This post has been edited by 808celica : May 19, 2013 - 2:43 PM...
6 posts • Started by 95CelicaST
[quote name='mkernz22' date='May 16, 2013 - 1:01 PM' post='1011463'] A full one? or just cat back A FULL ONE. ?Right ? lol i dont want it to be all **...
2 posts • Started by onnaj
Hello, I just finished my 4AGE 20V BT swap and today i let the garage check the CO value of the car and the oxygen sensor value. @ idle both values ar...
4 posts • Started by ActionClaw
(1995 Toyota Celica ST, 1.8L 7A-FE) I had some cooling system issues. I believe I may have found and repaired the problem but while looking I noticed ...
17 posts • Started by 1994Celica
2JZ all the way baby!!!!...
16 posts • Started by diZzyGOomba
+B to Fp...
2 posts • Started by onnaj
Did you mess with the screws inside the throttle bodies. Each Throttle body has an adjustment screw for idle. that sits at the very top. Another thing...
9 posts • Started by czwalga
For half the price of the fidanza you can get a really nice flywheel from F1 racing on ebay. I think it might be a little heavier than the fidanza, so...
1 posts • Started by yellowchinaman
Is this true? Does anyone know how much power the rev 4 block can handle?...
10 posts • Started by bsamps4
After taking my celi through an automatic car wash about a week ago i noticed a squeal coming from my passenger front. Before this i noticed a little ...
1 posts • Started by gts4
Looking to get some axle seals replaced. Are any of you willing to help out for $?...
14 posts • Started by Bitter
Also where to buy the fittings, brands, prices, hose prices and where to get them etc...
3 posts • Started by chacha
that's why i thought about the products above, but wasn't sure of the size of the connector and length to directly connect from master to slave. im s...
7 posts • Started by netrata
Hello, My BT swap is almost done, some obstacles i have to pass like vacuum obstacles I've enclosed 2 pictures can you guys tell me the vacuum lines o...
10 posts • Started by 1994Celica
1st warm day. Saw the engine temp jump at first to 70%, then sat down at 50% until I got home. Was driving for an hour. Also, it normally sits at 30%....
2 posts • Started by Smaay
Does the 7afe have a 2 peice oil pan I replaced the black ones oil gasket but it looks like theres a oil pan sub assembly above that. And also wheres ...
2 posts • Started by onnaj
Hello, I've noticed that the oil pressure sender on my 7AFE is completely different then the one on the 4AGE engine. I headr the 4AGE sender is digita...
5 posts • Started by DST94
Correction* Camry 95-99 axle will also work SC430 CV boot will work from 91-99 ST185 axles will swap perfectly hope it helps brother. good luck. This ...
6 posts • Started by Box
every day that thing runs will be a gift...
6 posts • Started by Smaay
200-250 for a complete 3s is a steal. Depends on what you are expecting to spend but you could be looking at the "might as well" syndrome. Might as w...